How To Make A Dead Lighter Work

Download Article

Sometimes a lighter tin get stuck or broken. By and large information technology'southward a quick prepare, simply it'south also very easy to buy a new 1. The first step is diagnosing what is wrong with your lighter, and and so yous tin get to work fixing it. Don't become frustrated if it doesn't work immediately - check all potential problems before you give up. If your lighter has sentimental value you may be able to go it working again.

1

Ensure that information technology isn't shattered. If yous broke the plastic part of your lighter then you lot'll need a new ane. The pressure is compromised and you won't exist able to use information technology anymore.
2

Look for rust, debris, or dirt. If you've left a lighter exterior for a long period of fourth dimension the metal bicycle on top might be rusted in place. If it won't spin, it won't light. If at that place is only dirt and droppings inside the lighter you lot might exist able to clean information technology out with your fingers or a pipe cleaner and get it going again. ^[i]

Advertising
three
Bank check the fuel tank. Luckily the nearly common trouble with these lighters is their incredibly pocket-sized fuel tank. When this no longer holds plenty fuel or plenty pressure, it needs to exist refilled.
- The most prone to mechanical and/or internal failure would exist the not-reusable Bic lighters.
4

Look to see if there is a spark. If there is no spark, that means that there is no flint. The flintstone is the slice of equipment that the wheel rubs confronting to create a spark. The spark lights the fuel and gives you a flame, so the flint is extremely important.
5

Check to run into if the flame is small, burns out, or isn't present at all. If the flame burns out then you could be running out of fuel. However, if you just recently bought the lighter there might exist an issue with the fuel reaching the spark.

1
Refuel your lighter. To do this for most lighters yous'll need to buy a butane can. You lot can buy 1 of these at your local hardware shop. Brand certain you bleed all of the remaining fuel out of your lighter beginning. Turn the lighter upside down with the fill valve facing upwards. Put pressure on the make full valve and go along the lighter away from your face and abroad from anything combustible. ^[2]
- Make sure the butane tin can nozzle fits in the hole in the bottom of the lighter. It has to fit in the upright position with the lighter on top of tin can. Yous'll desire to insert the nozzle so flip the whole contraption upside downwardly so that the lighter is nether the can. Now utilize pressure until you feel the metal of the lighter get cold. That means you've successfully gotten the butane inside.
- For a Nil lighter you'll have to buy Zippo lighter fluid from the Zippo online store.^[3]
- Keep in mind, it's probably merely easier to purchase a new lighter unless you lot are fastened to your electric current 1.
2
Replace your flint on a butane lighter. ^[4] The flint is the piece of equipment that creates the spark. Information technology's tiny black cylinder about a quarter inch long. To supervene upon the flint, remove the metallic surrounding the flame and the spark wheel. You'll accept to twist information technology out of position. Once you lot have removed the metallic you'll see that there is a spring. The bound should be about an inch to an inch and a half long. The flint is the modest piece of equipment that is well-nigh a quarter inch. Information technology will be black and cylindrical. The flint is used to brand the spark. Remove the flint from this leap. At present put in a new slice of flint. Reassembling the lighter is easy - put the flintstone in, stick the spring back in the pigsty, and so place the top back on.
- You lot can buy a new flintstone for 75 cents online.
3

Supplant your flint on a Zippo lighter. To supercede the flint, picture open the lighter, and pull up on the chimney. The chimney is the thing with five holes of each side of it. Yous'll want to pull until its all the way out. Nether the chimney there should be a piece of what looks like cotton wool that is held in place by a screw. Advisedly unscrew the spiral and pull information technology out along with the spring and small-scale piece of metallic within. Drop the new flint in, replace the spring, tighten the spiral, and replace the box dorsum in the lighter casing. Yous should be good to go. ^[v]
4

Remove the metallic that surrounds the flame hole if it is small or burns out. This means you take a problem with your fuel release. You tin can practice this with tweezers, needle-nose pliers, or annihilation else that works. Turn the nozzle from which the gas escapes counter-clockwise a few times. It might simply be too tight. If that doesn't work you might might demand to go yourself a new one. Luckily they aren't that expensive. ^[six]

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Bic lighters usually accept a child-proof safety-band over the spark wheel which can get quite annoying...simply to become rid of it just remove the metal the surrounds the flame and pull upward on the safety band until its free (with pliers or fingers)
The easiest way to remove the metal around the flame (or "chimney") would be to apply a blade or slender object to pry the side away from the button...just far enough to brand it over the latch that holds it in place
When refueling a Zippo, it helps to leave the lighter upside down for a few seconds or a minute later on having put more lighter fluid in
When tampering with any lighter, there is a run a risk of explosion... then exist conscientious

Advertizing

About This Article

Article Summary X

If your lighter isn't working, cheque to see if the fuel tank is empty or the flint is gone, as these are simple to set. Before you refuel your lighter, purchase a butane can, which can usually be found at a local hardware shop. To refuel, plow your lighter upside down and put force per unit area on the make full valve with the butane can nozzle. Once the nozzle is within, apply pressure until you feel the metal of the lighter get cold. Make certain to go along your lighter away from your face up and anything flammable. If your lighter needs a new flint, twist the metal that surrounds the flame until it comes off and yous can run across a jump. Then, replace the flint attached to the bound and reassemble your lighter. For more advice, similar how to replace the flint on a Nix lighter, scroll down.

Did this summary aid you?

Thanks to all authors for creating a page that has been read 512,213 times.